TK Truck Body located in Edmonton, Alberta, is a truck/van body manufacturer and fleet repair shop.
16445 130 Ave NW, Edmonton, AB T5V 1K5
Phone: 780 447 9529
Fax: 780 447 2468
We are available during scheduled operating hours to answer all inbound inquiries.
We are available during scheduled operating hours to answer all inbound inquiries.
Air receiver tanks are used for lowering compressor duty cycle and removing water from compressed air. Recommended for proper operation of all VMAC Hydraulic air compressor functions, including Standby Mode; manufactured to FMVSS 121 Standard; includes fittings, 160psi pressure relief valve, and tank drain. Maximum pressure: Up to 150 psi Dimensions: 32.0″ (l) x 8.0″ (d); 81.3 cm (l) x 20.3 cm (d) Weight: 23 lbs (10.4 kg)
Air receiver tanks are used for lowering compressor duty cycle and removing water from compressed air. Recommended for optimum operation of VMAC Hydraulic Air Compressors, VMAC Diesel Driven Air Compressors, UNDERHOOD40, UNDERHOOD70 (including Green Series Air Compressors), DTM70/DTM70-H, and VMAC Multifunction Power Systems, which include standby mode; ASME certified; includes fittings, 200 psi pressure relief valve, tank drain, and 200 psi pressure gauge. Maximum pressure: Up to 200 psi Dimensions: 30.0″ (l) x 10.0″ (d); 76.2 cm (l) x 25.4 cm (d) Weight: 33 lbs (15 kg)
Air receiver tanks are used for lowering compressor duty cycle and removing water from compressed air. Recommended for optimum operation of VMAC Diesel Air Compressors, Hydraulic Air Compressors, UNDERHOOD40, UNDERHOOD70 (including Green Series Air Compressors), DTM70/DTM70-H, and VMAC Multifunction Power Systems, which include standby mode; ASME certified; includes fittings, 200 psi pressure relief value, tank drain, and 200 psi pressure gauge. Maximum pressure: Up to 200 psi Dimensions: 73.75″ (l) x 14.0″ (d); 187.3 cm (l) x 35.6 cm (d) Weight: 95 lbs (43.1 kg)
Extends life of air tools; filter removes contaminants from the compressed air, adjustable regulator can reduce air pressure going to tools, and lubricator adds atomized tool oil to the air stream to lubricate air tools. Maximum flow: Up to 70 CFM / 150 psi Port size: 3/4″ NPT inlet and outlet
Improves performance and extends life of air tools; removes up to 80% of water from compressed air; includes automatic water drain. Maximum flow: 70 CFM / 175 psi Port size: 3/4″ NPT inlet and outlet Electrical: 12 V Dimensions: 17.0” (l) x 8.0” (w) x 14.5” (h); 43.2 cm (l) x 20.3 cm (w) x 36.8 cm (h) Weight: 35 lbs (15.8 kg)
Improves performance and extends life of air tools; removes up to 80% of water from compressed air; includes automatic water drain. Maximum flow: 70 CFM / 175 psi Port size: 3/4″ NPT inlet and outlet Electrical: 12 V Dimensions: 17.0” (l) x 8.0” (w) x 14.5” (h); 43.2 cm (l) x 20.3 cm (w) x 36.8 cm (h) Weight: 35 lbs (15.8 kg)
Extends life of air tools; filter removes contaminants from the compressed air, adjustable regulator can reduce air pressure going to tools, and lubricator adds atomized tool oil to the air stream to lubricate air tools. Maximum flow: Up to 70 CFM / 150 psi Port size: 3/4″ NPT inlet and outlet
Prevents freezing of the system pressure line and regulator in cold climates. Insulated rope heater includes on/off switch with indicator light. Dimensions: 10” Electrical: 12 V, 80 W Weight: 5 lbs (2.3 kg)
Air receiver tanks are used for lowering compressor duty cycle and removing water from compressed air. Recommended for optimum operation of VMAC Hydraulic Air Compressors, VMAC Diesel Driven Air Compressors, UNDERHOOD40, UNDERHOOD70 (including Green Series Air Compressors), DTM70/DTM70-H, and VMAC Multifunction Power Systems, which include standby mode; ASME certified; includes fittings, 200 psi pressure relief valve, tank drain, and 200 psi pressure gauge. Maximum pressure: Up to 200 psi Dimensions: 30.0″ (l) x 10.0″ (d); 76.2 cm (l) x 25.4 cm (d) Weight: 33 lbs (15 kg)
Air receiver tanks are used for lowering compressor duty cycle and removing water from compressed air. Recommended for optimum operation of VMAC Diesel Air Compressors, Hydraulic Air Compressors, UNDERHOOD40, UNDERHOOD70 (including Green Series Air Compressors), DTM70/DTM70-H, and VMAC Multifunction Power Systems, which include standby mode; ASME certified; includes fittings, 200 psi pressure relief value, tank drain, and 200 psi pressure gauge. Maximum pressure: Up to 200 psi Dimensions: 73.75″ (l) x 14.0″ (d); 187.3 cm (l) x 35.6 cm (d) Weight: 95 lbs (43.1 kg)
Cox Reel – P Series (P-LP-450RH) Sturdy single pedestal spring driven reel with space saving design facilitates workplace organization ½” x 50’ Max PSI: 300 Weight: Approx 48 lb Size: 7” x 18 5/8” x 17 1/8” External fluid path with machined from solid brass 90º full-flow NPT swivel inlet (Zinc plated steel swivel on HP models) Swivel Seals: NITRILE
Recommended for high duty cycle industrial and work truck hydraulic systems working in extreme hot climates, 100°F (37°C) and above; capable of removing up to 33,750 BTU / Hr. Hydraulic flow: 5-20 GPM (19-76 LPM) Pressure rating: Up to 500 psi (34.5 bar) Electrical: 12 V @ 10 Amps Dimensions: 17.0” (l) x 8.0” (w) x 13.0” (h); 43.2 cm (l) x 20.3 cm (w) x 33.0 cm (h) Weight: 30 lbs (13.5 kg)
3.5 – 8.0 GPM @ 3,265 psi Chelsea CGP-P11A026-5GC, Ford Displacement: 0.61 in3
4.9 – 10.7 GPM @ 3,265 psi Chelsea CGP-P11A037-5GC, Ford Displacement: 0.85 in3/rev
7.4 – 13.6 GPM @ 3,410 psi Chelsea CGP-P11A055-5GC, Ford Displacement: 1.28 in3/rev
8.1 – 14.9 GPM @ 3,265 psi Chelsea CGP-P11A061-5GE, Ford Displacement: 1.40 in3/rev
Prevents freezing of the system pressure line and regulator in cold climates. Insulated rope heater includes on/off switch with indicator light. Dimensions: 10” Electrical: 12 V, 80 W Weight: 5 lbs (2.3 kg)
Extends life of air tools; filter removes contaminants from the compressed air, adjustable regulator can reduce air pressure going to tools, and lubricator adds atomized tool oil to the air stream to lubricate air tools. Maximum flow: Up to 70 CFM / 150 psi Port size: 3/4″ NPT inlet and outlet
Improves performance and extends life of air tools; removes up to 80% of water from compressed air; includes automatic water drain. Maximum flow: 70 CFM / 175 psi Port size: 3/4″ NPT inlet and outlet Electrical: 12 V Dimensions: 17.0” (l) x 8.0” (w) x 14.5” (h); 43.2 cm (l) x 20.3 cm (w) x 36.8 cm (h) Weight: 35 lbs (15.8 kg)
Air receiver tanks are used for lowering compressor duty cycle and removing water from compressed air. Recommended for optimum operation of VMAC Hydraulic Air Compressors, VMAC Diesel Driven Air Compressors, UNDERHOOD40, UNDERHOOD70 (including Green Series Air Compressors), DTM70/DTM70-H, and VMAC Multifunction Power Systems, which include standby mode; ASME certified; includes fittings, 200 psi pressure relief valve, tank drain, and 200 psi pressure gauge. Maximum pressure: Up to 200 psi Dimensions: 30.0″ (l) x 10.0″ (d); 76.2 cm (l) x 25.4 cm (d) Weight: 33 lbs (15 kg)
Air receiver tanks are used for lowering compressor duty cycle and removing water from compressed air. Recommended for optimum operation of VMAC Diesel Air Compressors, Hydraulic Air Compressors, UNDERHOOD40, UNDERHOOD70 (including Green Series Air Compressors), DTM70/DTM70-H, and VMAC Multifunction Power Systems, which include standby mode; ASME certified; includes fittings, 200 psi pressure relief value, tank drain, and 200 psi pressure gauge. Maximum pressure: Up to 200 psi Dimensions: 73.75″ (l) x 14.0″ (d); 187.3 cm (l) x 35.6 cm (d) Weight: 95 lbs (43.1 kg)
Cox Reel – P Series (P-LP-450RH) Sturdy single pedestal spring driven reel with space saving design facilitates workplace organization ½” x 50’ Max PSI: 300 Weight: Approx 48 lb Size: 7” x 18 5/8” x 17 1/8” External fluid path with machined from solid brass 90º full-flow NPT swivel inlet (Zinc plated steel swivel on HP models) Swivel Seals: NITRILE
Cold climate heater package for operating the VMAC G30 Gas Driven Air Compressor in freezing climates; proven at temperatures of -30°C (-22°F); 120 V AC Heater; requires 600 W @ 5 Amps; (included with Stacked G30, optional with standard model.)
Remote control panel with ten foot extension for key switch, hour meter, choke, and unloader.
3 foot remote drain hose allows the engine oil to be easily drained.
Triple 4-gallon air receiver tanks with mounting frame; includes 200 psi pressure gauge, fittings, hose, ball valve and drain valves. Maximum pressure: Up to 150 psi Dimensions: 35.0” (l) x 20.5” (w) x 8.4” (h); 88.9 cm (l) x 52.0 cm (w) x 21.3 cm (h) Weight: 80 lbs (36 kg
Air receiver tanks are used for lowering compressor duty cycle and removing water from compressed air. Recommended for proper operation of all VMAC Hydraulic air compressor functions, including Standby Mode; manufactured to FMVSS 121 Standard; includes fittings, 160psi pressure relief valve, and tank drain. Maximum pressure: Up to 150 psi Dimensions: 32.0″ (l) x 8.0″ (d); 81.3 cm (l) x 20.3 cm (d) Weight: 23 lbs (10.4 kg)
Air receiver tanks are used for lowering compressor duty cycle and removing water from compressed air. Recommended for optimum operation of VMAC Hydraulic Air Compressors, VMAC Diesel Driven Air Compressors, UNDERHOOD40, UNDERHOOD70 (including Green Series Air Compressors), DTM70/DTM70-H, and VMAC Multifunction Power Systems, which include standby mode; ASME certified; includes fittings, 200 psi pressure relief valve, tank drain, and 200 psi pressure gauge. Maximum pressure: Up to 200 psi Dimensions: 30.0″ (l) x 10.0″ (d); 76.2 cm (l) x 25.4 cm (d) Weight: 33 lbs (15 kg)
Air receiver tanks are used for lowering compressor duty cycle and removing water from compressed air. Recommended for optimum operation of VMAC Diesel Air Compressors, Hydraulic Air Compressors, UNDERHOOD40, UNDERHOOD70 (including Green Series Air Compressors), DTM70/DTM70-H, and VMAC Multifunction Power Systems, which include standby mode; ASME certified; includes fittings, 200 psi pressure relief value, tank drain, and 200 psi pressure gauge. Maximum pressure: Up to 200 psi Dimensions: 73.75″ (l) x 14.0″ (d); 187.3 cm (l) x 35.6 cm (d) Weight: 95 lbs (43.1 kg)
Extends life of air tools; filter removes contaminants from the compressed air, adjustable regulator can reduce air pressure going to tools, and lubricator adds atomized tool oil to the air stream to lubricate air tools. Maximum flow: Up to 70 CFM / 150 psi Port size: 3/4″ NPT inlet and outlet
800 W, 12 V power inverter; required to power the VMAC G30 gas driven air compressor cold climate kit.
Cox Reel – P Series (P-LP-450RH) Sturdy single pedestal spring driven reel with space saving design facilitates workplace organization ½” x 50’ Max PSI: 300 Weight: Approx 48 lb Size: 7” x 18 5/8” x 17 1/8” External fluid path with machined from solid brass 90º full-flow NPT swivel inlet (Zinc plated steel swivel on HP models) Swivel Seals: NITRILE
Dual 4-gallon air receiver tanks with mounting frame; includes 200 psi pressure gauge, fittings, hose, ball valve and drain valves. Maximum pressure: Up to 150 psi
Durable 100% PVC Viny Mildew resistant Cold climate resistant to -40o Pressure washable up to 34 psi; washable with mild dish liquid Tear strength up to 130 lb Flame Resistant per CPAI-84 and NFPA701 Standards Four commercial grade webbing straps and quick release male/female toggles, with the female toggles staying fastened to the compressor unit mounting points Heavy duty zip to ease fitting and removal of cover.
Air receiver tanks are used for lowering compressor duty cycle and removing water from compressed air. Recommended for proper operation of all VMAC Hydraulic air compressor functions, including Standby Mode; manufactured to FMVSS 121 Standard; includes fittings, 160psi pressure relief valve, and tank drain. Maximum pressure: Up to 150 psi Dimensions: 32.0″ (l) x 8.0″ (d); 81.3 cm (l) x 20.3 cm (d) Weight: 23 lbs (10.4 kg)
Air receiver tanks are used for lowering compressor duty cycle and removing water from compressed air. Recommended for optimum operation of VMAC Hydraulic Air Compressors, VMAC Diesel Driven Air Compressors, UNDERHOOD40, UNDERHOOD70 (including Green Series Air Compressors), DTM70/DTM70-H, and VMAC Multifunction Power Systems, which include standby mode; ASME certified; includes fittings, 200 psi pressure relief valve, tank drain, and 200 psi pressure gauge. Maximum pressure: Up to 200 psi Dimensions: 30.0″ (l) x 10.0″ (d); 76.2 cm (l) x 25.4 cm (d) Weight: 33 lbs (15 kg)
Air receiver tanks are used for lowering compressor duty cycle and removing water from compressed air. Recommended for optimum operation of VMAC Diesel Air Compressors, Hydraulic Air Compressors, UNDERHOOD40, UNDERHOOD70 (including Green Series Air Compressors), DTM70/DTM70-H, and VMAC Multifunction Power Systems, which include standby mode; ASME certified; includes fittings, 200 psi pressure relief value, tank drain, and 200 psi pressure gauge. Maximum pressure: Up to 200 psi Dimensions: 73.75″ (l) x 14.0″ (d); 187.3 cm (l) x 35.6 cm (d) Weight: 95 lbs (43.1 kg)
Extends life of air tools; filter removes contaminants from the compressed air, adjustable regulator can reduce air pressure going to tools, and lubricator adds atomized tool oil to the air stream to lubricate air tools. Maximum flow: Up to 70 CFM / 150 psi Port size: 3/4″ NPT inlet and outlet
Improves performance and extends life of air tools; removes up to 80% of water from compressed air; includes automatic water drain. Maximum flow: 70 CFM / 175 psi Port size: 3/4″ NPT inlet and outlet Electrical: 12 V Dimensions: 17.0” (l) x 8.0” (w) x 14.5” (h); 43.2 cm (l) x 20.3 cm (w) x 36.8 cm (h) Weight: 35 lbs (15.8 kg)
Used for an easier and more rigid install, for mounting on thinner gauge service bodies; allows more airflow around the air compressor.
Converts 24 V power to 12 V, to allow the air compressor to be used on a 24 V electrical system.
Fully automated manifold heater block; recommended for extreme cold climates; when hydraulic oil temperatures fall below 5°F (-15°C), a solenoid will energize and heat the hydraulic oil.
Allows the 40 CFM VMAC Hydraulic air compressor to be used with variable displacement, pressure compensated (closed center) hydraulic systems.
VMAC’s Throttle Commander high idle electronic throttle controls speed up your truck’s engine when the vehicle is stationary. With the vehicle’s engine at high idle, more power is available for heavy alternator loads, cooling systems and Power Take-off (PTO) applications. This means jobs get done faster, saving time and money. Designed for electronic engines, these load sensing throttle controls will maintain preset programmed RPM settings over a range of engine torque loads. Can be activated from anywhere on the vehicle with a 12-volt signal. Benefits of VMAC Throttle Commander high idle controls: Maintains rpm over engine torque loads Easy installation – OEM connectors makes for a clean and simple installation Immediate response time 2-3 preset programmable RPM settings VMAC engineers throttle controls for the best performance and…
Recommended for high duty cycle industrial and work truck hydraulic systems working in extreme hot climates, 100°F (37°C) and above; capable of removing up to 33,750 BTU / Hr. Hydraulic flow: 5-20 GPM (19-76 LPM) Pressure rating: Up to 500 psi (34.5 bar) Electrical: 12 V @ 10 Amps Dimensions: 17.0” (l) x 8.0” (w) x 13.0” (h); 43.2 cm (l) x 20.3 cm (w) x 33.0 cm (h) Weight: 30 lbs (13.5 kg)
Cox Reel – P Series (P-LP-450RH) Sturdy single pedestal spring driven reel with space saving design facilitates workplace organization ½” x 50’ Max PSI: 300 Weight: Approx 48 lb Size: 7” x 18 5/8” x 17 1/8” External fluid path with machined from solid brass 90º full-flow NPT swivel inlet (Zinc plated steel swivel on HP models) Swivel Seals: NITRILE
Air receiver tanks are used for lowering compressor duty cycle and removing water from compressed air. Recommended for proper operation of all VMAC Hydraulic air compressor functions, including Standby Mode; manufactured to FMVSS 121 Standard; includes fittings, 160psi pressure relief valve, and tank drain. Maximum pressure: Up to 150 psi Dimensions: 32.0″ (l) x 8.0″ (d); 81.3 cm (l) x 20.3 cm (d) Weight: 23 lbs (10.4 kg)
Air receiver tanks are used for lowering compressor duty cycle and removing water from compressed air. Recommended for optimum operation of VMAC Hydraulic Air Compressors, VMAC Diesel Driven Air Compressors, UNDERHOOD40, UNDERHOOD70 (including Green Series Air Compressors), DTM70/DTM70-H, and VMAC Multifunction Power Systems, which include standby mode; ASME certified; includes fittings, 200 psi pressure relief valve, tank drain, and 200 psi pressure gauge. Maximum pressure: Up to 200 psi Dimensions: 30.0″ (l) x 10.0″ (d); 76.2 cm (l) x 25.4 cm (d) Weight: 33 lbs (15 kg
Air receiver tanks are used for lowering compressor duty cycle and removing water from compressed air. Recommended for optimum operation of VMAC Diesel Air Compressors, Hydraulic Air Compressors, UNDERHOOD40, UNDERHOOD70 (including Green Series Air Compressors), DTM70/DTM70-H, and VMAC Multifunction Power Systems, which include standby mode; ASME certified; includes fittings, 200 psi pressure relief value, tank drain, and 200 psi pressure gauge. Maximum pressure: Up to 200 psi Dimensions: 73.75″ (l) x 14.0″ (d); 187.3 cm (l) x 35.6 cm (d) Weight: 95 lbs (43.1 kg)
Air receiver tanks are used for lowering compressor duty cycle and removing water from compressed air. Recommended for optimum operation of VMAC Diesel Air Compressors, Hydraulic Air Compressors, UNDERHOOD40, UNDERHOOD70 (including Green Series Air Compressors), DTM70/DTM70-H, and VMAC Multifunction Power Systems, which include standby mode; ASME certified; includes fittings, 200 psi pressure relief value, tank drain, and 200 psi pressure gauge. Maximum pressure: Up to 200 psi Dimensions: 73.75″ (l) x 14.0″ (d); 187.3 cm (l) x 35.6 cm (d) Weight: 95 lbs (43.1 kg)
Improves performance and extends life of air tools; removes up to 80% of water from compressed air; includes automatic water drain. Maximum flow: 70 CFM / 175 psi Port size: 3/4″ NPT inlet and outlet Electrical: 12 V Dimensions: 17.0” (l) x 8.0” (w) x 14.5” (h); 43.2 cm (l) x 20.3 cm (w) x 36.8 cm (h) Weight: 35 lbs (15.8 kg)
Used for an easier and more rigid install, for mounting on thinner gauge service bodies; allows more airflow around the air compressor.
Converts 24 V power to 12 V, to allow the air compressor to be used on a 24 V electrical system.
Recommended for high duty cycle industrial and work truck hydraulic systems working in extreme hot climates, 100°F (37°C) and above; capable of removing up to 33,750 BTU / Hr. Hydraulic flow: 5-20 GPM (19-76 LPM) Pressure rating: Up to 500 psi (34.5 bar) Electrical: 12 V @ 10 Amps Dimensions: 17.0” (l) x 8.0” (w) x 13.0” (h); 43.2 cm (l) x 20.3 cm (w) x 33.0 cm (h) Weight: 30 lbs (13.5 kg)
VMAC’s Throttle Commander high idle electronic throttle controls speed up your truck’s engine when the vehicle is stationary. With the vehicle’s engine at high idle, more power is available for heavy alternator loads, cooling systems and Power Take-off (PTO) applications. This means jobs get done faster, saving time and money. Designed for electronic engines, these load sensing throttle controls will maintain preset programmed RPM settings over a range of engine torque loads. Can be activated from anywhere on the vehicle with a 12-volt signal. Benefits of VMAC Throttle Commander high idle controls: Maintains rpm over engine torque loads Easy installation – OEM connectors makes for a clean and simple installation Immediate response time 2-3 preset programmable RPM settings VMAC engineers throttle controls for the best performance and…
Fully automated manifold heater block; recommended for extreme cold climates; when hydraulic oil temperatures fall below 5°F (-15°C), a solenoid will energize and heat the hydraulic oil.
Extends life of air tools; filter removes contaminants from the compressed air, adjustable regulator can reduce air pressure going to tools, and lubricator adds atomized tool oil to the air stream to lubricate air tools. Maximum flow: Up to 70 CFM / 150 psi Port size: 3/4″ NPT inlet and outlet
Cox Reel – P Series (P-LP-450RH) Sturdy single pedestal spring driven reel with space saving design facilitates workplace organization ½” x 50’ Max PSI: 300 Weight: Approx 48 lb Size: 7” x 18 5/8” x 17 1/8” External fluid path with machined from solid brass 90º full-flow NPT swivel inlet (Zinc plated steel swivel on HP models) Swivel Seals: NITRILE
Allows the VMAC Multifunction to be controlled with various crane remotes; converts latching or momentary switched 12 V signals into the low-side switching required by the VMAC Multifunction control system.
External Diesel Fuel Pump allows the VMAC diesel driven air compressor to be tied into the vehicles diesel fuel tank; mounts externally; activates automatically when the air compressor key switch is in RUN position and disables automatically when air compressor enters Standby Mode or key switch is turned the OFF position.
1,750 W, 12 V power inverter; required to power the VMAC diesel driven air compressor cold climate kit.
Remote control panel for the 1,750 W power inverter; shows status and has an on/off button.
Air receiver tanks are used for lowering compressor duty cycle and removing water from compressed air. Recommended for proper operation of all VMAC Hydraulic air compressor functions, including Standby Mode; manufactured to FMVSS 121 Standard; includes fittings, 160psi pressure relief valve, and tank drain. Maximum pressure: Up to 150 psi Dimensions: 32.0″ (l) x 8.0″ (d); 81.3 cm (l) x 20.3 cm (d) Weight: 23 lbs (10.4 kg)
Air receiver tanks are used for lowering compressor duty cycle and removing water from compressed air. Recommended for optimum operation of VMAC Hydraulic Air Compressors, VMAC Diesel Driven Air Compressors, UNDERHOOD40, UNDERHOOD70 (including Green Series Air Compressors), DTM70/DTM70-H, and VMAC Multifunction Power Systems, which include standby mode; ASME certified; includes fittings, 200 psi pressure relief valve, tank drain, and 200 psi pressure gauge. Maximum pressure: Up to 200 psi Dimensions: 30.0″ (l) x 10.0″ (d); 76.2 cm (l) x 25.4 cm (d) Weight: 33 lbs (15 kg)
Air receiver tanks are used for lowering compressor duty cycle and removing water from compressed air. Recommended for optimum operation of VMAC Diesel Air Compressors, Hydraulic Air Compressors, UNDERHOOD40, UNDERHOOD70 (including Green Series Air Compressors), DTM70/DTM70-H, and VMAC Multifunction Power Systems, which include standby mode; ASME certified; includes fittings, 200 psi pressure relief value, tank drain, and 200 psi pressure gauge. Maximum pressure: Up to 200 psi Dimensions: 73.75″ (l) x 14.0″ (d); 187.3 cm (l) x 35.6 cm (d) Weight: 95 lbs (43.1 kg)
Extends life of air tools; filter removes contaminants from the compressed air, adjustable regulator can reduce air pressure going to tools, and lubricator adds atomized tool oil to the air stream to lubricate air tools. Maximum flow: Up to 70 CFM / 150 psi Port size: 3/4″ NPT inlet and outlet
Improves performance and extends life of air tools; removes up to 80% of water from compressed air; includes automatic water drain. Maximum flow: 70 CFM / 175 psi Port size: 3/4″ NPT inlet and outlet Electrical: 12 V Dimensions: 17.0” (l) x 8.0” (w) x 14.5” (h); 43.2 cm (l) x 20.3 cm (w) x 36.8 cm (h) Weight: 35 lbs (15.8 kg)
5 GPM hydraulic pump for VMAC Multifunction Power Systems equipped with PTO; factory installed. Hydraulic flow: Up to 5 GPM @ 3,500 psi (18.9 LPM @ 241 bar) Note: PTO must be installed on VMAC Multifunction Power System.
8 GPM hydraulic pump for VMAC Multifunction Power Systems equipped with PTO; factory installed. Hydraulic flow: Up to 8 GPM @ 3,500 psi (30.3 LPM @ 241 bar) Note: PTO must be installed on VMAC Multifunction Power System.
10 GPM hydraulic pump for VMAC Multifunction Power Systems equipped with PTO; factory installed. Hydraulic flow: Up to 10 GPM @ 3,500 psi (37.9 LPM @ 241 bar) Note: PTO must be installed on VMAC Multifunction Power System.
Cox Reel – P Series (P-LP-450RH) Sturdy single pedestal spring driven reel with space saving design facilitates workplace organization ½” x 50’ Max PSI: 300 Weight: Approx 48 lb Size: 7” x 18 5/8” x 17 1/8” External fluid path with machined from solid brass 90º full-flow NPT swivel inlet (Zinc plated steel swivel on HP models) Swivel Seals: NITRILE
7-gallon diesel fuel tank mounts directly to VMAC Multifunction Power System; includes mechanical fuel gauge and low-fuel shut-off sensor. Fuel Capacity: 7-Gallons Dimensions: 18.0” (l) x 4.75” (w) x 20.63” (h); 45.7 cm (l) x 12.1 cm (w) x 52.4 cm (h) Weight (dry): 25 lbs (11.3 kg)
7-gallon diesel fuel tank mounts directly to VMAC Multifunction Power System; includes mechanical fuel gauge and low-fuel shut-off sensor. Fuel Capacity: 7-Gallons Dimensions: 18.0” (l) x 4.75” (w) x 20.63” (h); 45.7 cm (l) x 12.1 cm (w) x 52.4 cm (h) Weight (dry): 25 lbs (11.3 kg)
External Diesel Fuel Pump allows the VMAC diesel driven air compressor to be tied into the vehicles diesel fuel tank; mounts externally; activates automatically when the air compressor key switch is in RUN position and disables automatically when air compressor enters Standby Mode or key switch is turned the OFF position.
1,750 W, 12 V power inverter; required to power the VMAC diesel driven air compressor cold climate kit.
Remote control panel for the 1,750 W power inverter; shows status and has an on/off button.
Allows the VMAC Multifunction to be controlled with various crane remotes; converts latching or momentary switched 12 V signals into the low-side switching required by the VMAC Multifunction control system.
Air receiver tanks are used for lowering compressor duty cycle and removing water from compressed air. Recommended for proper operation of all VMAC Hydraulic air compressor functions, including Standby Mode; manufactured to FMVSS 121 Standard; includes fittings, 160psi pressure relief valve, and tank drain. Maximum pressure: Up to 150 psi Dimensions: 32.0″ (l) x 8.0″ (d); 81.3 cm (l) x 20.3 cm (d) Weight: 23 lbs (10.4 kg)
Air receiver tanks are used for lowering compressor duty cycle and removing water from compressed air. Recommended for optimum operation of VMAC Hydraulic Air Compressors, VMAC Diesel Driven Air Compressors, UNDERHOOD40, UNDERHOOD70 (including Green Series Air Compressors), DTM70/DTM70-H, and VMAC Multifunction Power Systems, which include standby mode; ASME certified; includes fittings, 200 psi pressure relief valve, tank drain, and 200 psi pressure gauge. Maximum pressure: Up to 200 psi Dimensions: 30.0″ (l) x 10.0″ (d); 76.2 cm (l) x 25.4 cm (d) Weight: 33 lbs (15 kg)
Air receiver tanks are used for lowering compressor duty cycle and removing water from compressed air. Recommended for optimum operation of VMAC Diesel Air Compressors, Hydraulic Air Compressors, UNDERHOOD40, UNDERHOOD70 (including Green Series Air Compressors), DTM70/DTM70-H, and VMAC Multifunction Power Systems, which include standby mode; ASME certified; includes fittings, 200 psi pressure relief value, tank drain, and 200 psi pressure gauge. Maximum pressure: Up to 200 psi Dimensions: 73.75″ (l) x 14.0″ (d); 187.3 cm (l) x 35.6 cm (d) Weight: 95 lbs (43.1 kg)
Extends life of air tools; filter removes contaminants from the compressed air, adjustable regulator can reduce air pressure going to tools, and lubricator adds atomized tool oil to the air stream to lubricate air tools. Maximum flow: Up to 70 CFM / 150 psi Port size: 3/4″ NPT inlet and outlet
Improves performance and extends life of air tools; removes up to 80% of water from compressed air; includes automatic water drain. Maximum flow: 70 CFM / 175 psi Port size: 3/4″ NPT inlet and outlet Electrical: 12 V Dimensions: 17.0” (l) x 8.0” (w) x 14.5” (h); 43.2 cm (l) x 20.3 cm (w) x 36.8 cm (h) Weight: 35 lbs (15.8 kg)
Cox Reel – P Series (P-LP-450RH) Sturdy single pedestal spring driven reel with space saving design facilitates workplace organization ½” x 50’ Max PSI: 300 Weight: Approx 48 lb Size: 7” x 18 5/8” x 17 1/8” External fluid path with machined from solid brass 90º full-flow NPT swivel inlet (Zinc plated steel swivel on HP models) Swivel Seals: NITRILE
7-gallon diesel fuel tank mounts directly to VMAC Multifunction Power System; includes mechanical fuel gauge and low-fuel shut-off sensor. Fuel Capacity: 7-Gallons Dimensions: 18.0” (l) x 4.75” (w) x 20.63” (h); 45.7 cm (l) x 12.1 cm (w) x 52.4 cm (h) Weight (dry): 25 lbs (11.3 kg)
External Diesel Fuel Pump allows the VMAC diesel driven air compressor to be tied into the vehicles diesel fuel tank; mounts externally; activates automatically when the air compressor key switch is in RUN position and disables automatically when air compressor enters Standby Mode or key switch is turned the OFF position.
1,750 W, 12 V power inverter; required to power the VMAC diesel driven air compressor cold climate kit.
Remote control panel for the 1,750 W power inverter; shows status and has an on/off button.
Allows the VMAC Multifunction to be controlled with various crane remotes; converts latching or momentary switched 12 V signals into the low-side switching required by the VMAC Multifunction control system.
Air receiver tanks are used for lowering compressor duty cycle and removing water from compressed air. Recommended for proper operation of all VMAC Hydraulic air compressor functions, including Standby Mode; manufactured to FMVSS 121 Standard; includes fittings, 160psi pressure relief valve, and tank drain. Maximum pressure: Up to 150 psi Dimensions: 32.0″ (l) x 8.0″ (d); 81.3 cm (l) x 20.3 cm (d) Weight: 23 lbs (10.4 kg)
Air receiver tanks are used for lowering compressor duty cycle and removing water from compressed air. Recommended for optimum operation of VMAC Hydraulic Air Compressors, VMAC Diesel Driven Air Compressors, UNDERHOOD40, UNDERHOOD70 (including Green Series Air Compressors), DTM70/DTM70-H, and VMAC Multifunction Power Systems, which include standby mode; ASME certified; includes fittings, 200 psi pressure relief valve, tank drain, and 200 psi pressure gauge. Maximum pressure: Up to 200 psi Dimensions: 30.0″ (l) x 10.0″ (d); 76.2 cm (l) x 25.4 cm (d) Weight: 33 lbs (15 kg)
Air receiver tanks are used for lowering compressor duty cycle and removing water from compressed air. Recommended for optimum operation of VMAC Diesel Air Compressors, Hydraulic Air Compressors, UNDERHOOD40, UNDERHOOD70 (including Green Series Air Compressors), DTM70/DTM70-H, and VMAC Multifunction Power Systems, which include standby mode; ASME certified; includes fittings, 200 psi pressure relief value, tank drain, and 200 psi pressure gauge. Maximum pressure: Up to 200 psi Dimensions: 73.75″ (l) x 14.0″ (d); 187.3 cm (l) x 35.6 cm (d) Weight: 95 lbs (43.1 kg)
Extends life of air tools; filter removes contaminants from the compressed air, adjustable regulator can reduce air pressure going to tools, and lubricator adds atomized tool oil to the air stream to lubricate air tools. Maximum flow: Up to 70 CFM / 150 psi Port size: 3/4″ NPT inlet and outlet
Improves performance and extends life of air tools; removes up to 80% of water from compressed air; includes automatic water drain. Maximum flow: 70 CFM / 175 psi Port size: 3/4″ NPT inlet and outlet Electrical: 12 V Dimensions: 17.0” (l) x 8.0” (w) x 14.5” (h); 43.2 cm (l) x 20.3 cm (w) x 36.8 cm (h) Weight: 35 lbs (15.8 kg)
Cox Reel – P Series (P-LP-450RH) Sturdy single pedestal spring driven reel with space saving design facilitates workplace organization ½” x 50’ Max PSI: 300 Weight: Approx 48 lb Size: 7” x 18 5/8” x 17 1/8” External fluid path with machined from solid brass 90º full-flow NPT swivel inlet (Zinc plated steel swivel on HP models) Swivel Seals: NITRILE
7-gallon diesel fuel tank mounts directly to VMAC Multifunction Power System; includes mechanical fuel gauge and low-fuel shut-off sensor. Fuel Capacity: 7-Gallons Dimensions: 18.0” (l) x 4.75” (w) x 20.63” (h); 45.7 cm (l) x 12.1 cm (w) x 52.4 cm (h) Weight (dry): 25 lbs (11.3 kg)
External Diesel Fuel Pump allows the VMAC diesel driven air compressor to be tied into the vehicles diesel fuel tank; mounts externally; activates automatically when the air compressor key switch is in RUN position and disables automatically when air compressor enters Standby Mode or key switch is turned the OFF position.
1,750 W, 12 V power inverter; required to power the VMAC diesel driven air compressor cold climate kit.
Remote control panel for the 1,750 W power inverter; shows status and has an on/off button.
Allows the VMAC Multifunction to be controlled with various crane remotes; converts latching or momentary switched 12 V signals into the low-side switching required by the VMAC Multifunction control system.
Air receiver tanks are used for lowering compressor duty cycle and removing water from compressed air. Recommended for proper operation of all VMAC Hydraulic air compressor functions, including Standby Mode; manufactured to FMVSS 121 Standard; includes fittings, 160psi pressure relief valve, and tank drain. Maximum pressure: Up to 150 psi Dimensions: 32.0″ (l) x 8.0″ (d); 81.3 cm (l) x 20.3 cm (d) Weight: 23 lbs (10.4 kg)
Air receiver tanks are used for lowering compressor duty cycle and removing water from compressed air. Recommended for optimum operation of VMAC Hydraulic Air Compressors, VMAC Diesel Driven Air Compressors, UNDERHOOD40, UNDERHOOD70 (including Green Series Air Compressors), DTM70/DTM70-H, and VMAC Multifunction Power Systems, which include standby mode; ASME certified; includes fittings, 200 psi pressure relief valve, tank drain, and 200 psi pressure gauge. Maximum pressure: Up to 200 psi Dimensions: 30.0″ (l) x 10.0″ (d); 76.2 cm (l) x 25.4 cm (d) Weight: 33 lbs (15 kg)
Air receiver tanks are used for lowering compressor duty cycle and removing water from compressed air. Recommended for optimum operation of VMAC Diesel Air Compressors, Hydraulic Air Compressors, UNDERHOOD40, UNDERHOOD70 (including Green Series Air Compressors), DTM70/DTM70-H, and VMAC Multifunction Power Systems, which include standby mode; ASME certified; includes fittings, 200 psi pressure relief value, tank drain, and 200 psi pressure gauge. Maximum pressure: Up to 200 psi Dimensions: 73.75″ (l) x 14.0″ (d); 187.3 cm (l) x 35.6 cm (d) Weight: 95 lbs (43.1 kg)
Extends life of air tools; filter removes contaminants from the compressed air, adjustable regulator can reduce air pressure going to tools, and lubricator adds atomized tool oil to the air stream to lubricate air tools. Maximum flow: Up to 70 CFM / 150 psi Port size: 3/4″ NPT inlet and outlet
Improves performance and extends life of air tools; removes up to 80% of water from compressed air; includes automatic water drain. Maximum flow: 70 CFM / 175 psi Port size: 3/4″ NPT inlet and outlet Electrical: 12 V Dimensions: 17.0” (l) x 8.0” (w) x 14.5” (h); 43.2 cm (l) x 20.3 cm (w) x 36.8 cm (h) Weight: 35 lbs (15.8 kg)
10 GPM hydraulic pump for VMAC Multifunction Power Systems equipped with PTO; factory installed. Hydraulic flow: Up to 10 GPM @ 3,500 psi (37.9 LPM @ 241 bar) Note: PTO must be installed on VMAC Multifunction Power System.
8 GPM hydraulic pump for VMAC Multifunction Power Systems equipped with PTO; factory installed. Hydraulic flow: Up to 8 GPM @ 3,500 psi (30.3 LPM @ 241 bar) Note: PTO must be installed on VMAC Multifunction Power System.
5 GPM hydraulic pump for VMAC Multifunction Power Systems equipped with PTO; factory installed. Hydraulic flow: Up to 5 GPM @ 3,500 psi (18.9 LPM @ 241 bar) Note: PTO must be installed on VMAC Multifunction Power System.
Cox Reel – P Series (P-LP-450RH) Sturdy single pedestal spring driven reel with space saving design facilitates workplace organization ½” x 50’ Max PSI: 300 Weight: Approx 48 lb Size: 7” x 18 5/8” x 17 1/8” External fluid path with machined from solid brass 90º full-flow NPT swivel inlet (Zinc plated steel swivel on HP models) Swivel Seals: NITRILE
Extends life of air tools; filter removes contaminants from the compressed air, adjustable regulator can reduce air pressure going to tools, and lubricator adds atomized tool oil to the air stream to lubricate air tools. Maximum flow: Up to 185 CFM / 200 psi Port size: 1″ NPT inlet and outlet
Improves performance and extends life of air tools; removes up to 80% of water from compressed air; includes automatic water drain. Includes Filter Regulator Lubricator (FRL). Maximum flow: 185 CFM / 200 psi Port size: 1″ NPT inlet and outlet Electrical: 12 V Dimensions (not including FRL): 17.0” (l) x 8.0” (w) x 14.5” (h); 43.2 cm (l) x 20.3 cm (w) x 36.8 cm (h) Weight: 45 lbs (20.4 kg)
Prevents freezing of the system pressure line and regulator in cold climates. Insulated rope heater includes on/off switch with indicator light. Dimensions: 10” Electrical: 12 V, 80 W Weight: 5 lbs (2.3 kg)
Air receiver tanks are used for lowering compressor duty cycle and removing water from compressed air. Recommended for optimum operation of VMAC Hydraulic Air Compressors, VMAC Diesel Driven Air Compressors, UNDERHOOD40, UNDERHOOD70 (including Green Series Air Compressors), DTM70/DTM70-H, and VMAC Multifunction Power Systems, which include standby mode; ASME certified; includes fittings, 200 psi pressure relief valve, tank drain, and 200 psi pressure gauge. Maximum pressure: Up to 200 psi Dimensions: 30.0″ (l) x 10.0″ (d); 76.2 cm (l) x 25.4 cm (d) Weight: 33 lbs (15 kg)
Air receiver tanks are used for lowering compressor duty cycle and removing water from compressed air. Recommended for optimum operation of VMAC Diesel Air Compressors, Hydraulic Air Compressors, UNDERHOOD40, UNDERHOOD70 (including Green Series Air Compressors), DTM70/DTM70-H, and VMAC Multifunction Power Systems, which include standby mode; ASME certified; includes fittings, 200 psi pressure relief value, tank drain, and 200 psi pressure gauge. Maximum pressure: Up to 200 psi Dimensions: 73.75″ (l) x 14.0″ (d); 187.3 cm (l) x 35.6 cm (d) Weight: 95 lbs (43.1 kg)
Extends life of air tools; filter removes contaminants from the compressed air, adjustable regulator can reduce air pressure going to tools, and lubricator adds atomized tool oil to the air stream to lubricate air tools. Maximum flow: Up to 70 CFM / 150 psi Port size: 3/4″ NPT inlet and outlet
Improves performance and extends life of air tools; removes up to 80% of water from compressed air; includes automatic water drain. Maximum flow: 70 CFM / 175 psi Port size: 3/4″ NPT inlet and outlet Electrical: 12 V Dimensions: 17.0” (l) x 8.0” (w) x 14.5” (h); 43.2 cm (l) x 20.3 cm (w) x 36.8 cm (h) Weight: 35 lbs (15.8 kg)
Cox Reel – P Series (P-LP-450RH) Sturdy single pedestal spring driven reel with space saving design facilitates workplace organization ½” x 50’ Max PSI: 300 Weight: Approx 48 lb Size: 7” x 18 5/8” x 17 1/8” External fluid path with machined from solid brass 90º full-flow NPT swivel inlet (Zinc plated steel swivel on HP models) Swivel Seals: NITRILE
Heavy duty compressor air filter for moderate dust environments. Dimensions: 14.0” (l) x 6.0” (w) x 12.0” (h); 35.6 cm (l) x 15.2 cm (w) x 30.5 cm (h) Maximum flow: 80 CFM Weight: 10 lbs (4.5 kg)
Heavy duty compressor air filter for moderate and heavy dust environments. Dimensions: 14.0” (l) x 6.0” (w) x 12.0” (h); 35.6 cm (l) x 15.2 cm (w) x 30.5 cm (h) Maximum flow: 80 CFM Weight: 10 lbs (4.5 kg)
Air receiver tanks are used for lowering compressor duty cycle and removing water from compressed air. Recommended for optimum operation of VMAC Diesel Air Compressors, Hydraulic Air Compressors, UNDERHOOD40, UNDERHOOD70 (including Green Series Air Compressors), DTM70/DTM70-H, and VMAC Multifunction Power Systems, which include standby mode; ASME certified; includes fittings, 200 psi pressure relief value, tank drain, and 200 psi pressure gauge. Maximum pressure: Up to 200 psi Dimensions: 73.75″ (l) x 14.0″ (d); 187.3 cm (l) x 35.6 cm (d) Weight: 95 lbs (43.1 kg)
Air receiver tanks are used for lowering compressor duty cycle and removing water from compressed air. Recommended for optimum operation of VMAC Hydraulic Air Compressors, VMAC Diesel Driven Air Compressors, UNDERHOOD40, UNDERHOOD70 (including Green Series Air Compressors), DTM70/DTM70-H, and VMAC Multifunction Power Systems, which include standby mode; ASME certified; includes fittings, 200 psi pressure relief valve, tank drain, and 200 psi pressure gauge. Maximum pressure: Up to 200 psi Dimensions: 30.0″ (l) x 10.0″ (d); 76.2 cm (l) x 25.4 cm (d) Weight: 33 lbs (15 kg)
Air receiver tanks are used for lowering compressor duty cycle and removing water from compressed air. Recommended for proper operation of all VMAC Hydraulic air compressor functions, including Standby Mode; manufactured to FMVSS 121 Standard; includes fittings, 160psi pressure relief valve, and tank drain. Maximum pressure: Up to 150 psi Dimensions: 32.0″ (l) x 8.0″ (d); 81.3 cm (l) x 20.3 cm (d) Weight: 23 lbs (10.4 kg)
The WHASP tank automatically depressurizes to prevent the clutch from starting while there is air pressure in the system, this is done to extend the life of the clutch and belt. The A700224 WHASP tank remote mount muffler kit is designed to relocate the blowdown muffler to an external location. This is recommended for applications where the WHASP tank will be located inside of a van or service body, the remote mounted muffler will reduce cabin noise when the compressor blowdown operates, and will ensure that any oil vapor will be safely discharged outside of the vehicle.
Improves performance and extends life of air tools; removes up to 80% of water from compressed air; includes automatic water drain. Maximum flow: 70 CFM / 175 psi Port size: 3/4″ NPT inlet and outlet Electrical: 12 V Dimensions: 17.0” (l) x 8.0” (w) x 14.5” (h); 43.2 cm (l) x 20.3 cm (w) x 36.8 cm (h) Weight: 35 lbs (15.8 kg)
Extends life of air tools; filter removes contaminants from the compressed air, adjustable regulator can reduce air pressure going to tools, and lubricator adds atomized tool oil to the air stream to lubricate air tools. Maximum flow: Up to 70 CFM / 150 psi Port size: 3/4″ NPT inlet and outlet
Air receiver tanks are used for lowering compressor duty cycle and removing water from compressed air. Recommended for proper operation of all VMAC Hydraulic air compressor functions, including Standby Mode; manufactured to FMVSS 121 Standard; includes fittings, 160psi pressure relief valve, and tank drain. Maximum pressure: Up to 150 psi Dimensions: 32.0″ (l) x 8.0″ (d); 81.3 cm (l) x 20.3 cm (d) Weight: 23 lbs (10.4 kg)
Air receiver tanks are used for lowering compressor duty cycle and removing water from compressed air. Recommended for optimum operation of VMAC Hydraulic Air Compressors, VMAC Diesel Driven Air Compressors, UNDERHOOD40, UNDERHOOD70 (including Green Series Air Compressors), DTM70/DTM70-H, and VMAC Multifunction Power Systems, which include standby mode; ASME certified; includes fittings, 200 psi pressure relief valve, tank drain, and 200 psi pressure gauge. Maximum pressure: Up to 200 psi Dimensions: 30.0″ (l) x 10.0″ (d); 76.2 cm (l) x 25.4 cm (d) Weight: 33 lbs (15 kg)
Air receiver tanks are used for lowering compressor duty cycle and removing water from compressed air. Recommended for optimum operation of VMAC Diesel Air Compressors, Hydraulic Air Compressors, UNDERHOOD40, UNDERHOOD70 (including Green Series Air Compressors), DTM70/DTM70-H, and VMAC Multifunction Power Systems, which include standby mode; ASME certified; includes fittings, 200 psi pressure relief value, tank drain, and 200 psi pressure gauge. Maximum pressure: Up to 200 psi Dimensions: 73.75″ (l) x 14.0″ (d); 187.3 cm (l) x 35.6 cm (d) Weight: 95 lbs (43.1 kg)
Cox Reel – P Series (P-LP-450RH) Sturdy single pedestal spring driven reel with space saving design facilitates workplace organization ½” x 50’ Max PSI: 300 Weight: Approx 48 lb Size: 7” x 18 5/8” x 17 1/8” External fluid path with machined from solid brass 90º full-flow NPT swivel inlet (Zinc plated steel swivel on HP models) Swivel Seals: NITRILE
The WHASP tank automatically depressurizes to prevent the clutch from starting while there is air pressure in the system, this is done to extend the life of the clutch and belt. The A700224 WHASP tank remote mount muffler kit is designed to relocate the blowdown muffler to an external location. This is recommended for applications where the WHASP tank will be located inside of a van or service body, the remote mounted muffler will reduce cabin noise when the compressor blowdown operates, and will ensure that any oil vapor will be safely discharged outside of the vehicle.
Extends life of air tools; filter removes contaminants from the compressed air, adjustable regulator can reduce air pressure going to tools, and lubricator adds atomized tool oil to the air stream to lubricate air tools. Maximum flow: Up to 70 CFM / 150 psi Port size: 3/4″ NPT inlet and outlet
Prevents freezing of the system pressure line and regulator in cold climates. Insulated rope heater includes on/off switch with indicator light. Dimensions: 10” Electrical: 12 V, 80 W Weight: 5 lbs (2.3 kg)
Improves performance and extends life of air tools; removes up to 80% of water from compressed air; includes automatic water drain. Maximum flow: 70 CFM / 175 psi Port size: 3/4″ NPT inlet and outlet Electrical: 12 V Dimensions: 17.0” (l) x 8.0” (w) x 14.5” (h); 43.2 cm (l) x 20.3 cm (w) x 36.8 cm (h) Weight: 35 lbs (15.8 kg)
Air receiver tanks are used for lowering compressor duty cycle and removing water from compressed air. Recommended for optimum operation of VMAC Hydraulic Air Compressors, VMAC Diesel Driven Air Compressors, UNDERHOOD40, UNDERHOOD70 (including Green Series Air Compressors), DTM70/DTM70-H, and VMAC Multifunction Power Systems, which include standby mode; ASME certified; includes fittings, 200 psi pressure relief valve, tank drain, and 200 psi pressure gauge. Maximum pressure: Up to 200 psi Dimensions: 30.0″ (l) x 10.0″ (d); 76.2 cm (l) x 25.4 cm (d) Weight: 33 lbs (15 kg)
Air receiver tanks are used for lowering compressor duty cycle and removing water from compressed air. Recommended for optimum operation of VMAC Diesel Air Compressors, Hydraulic Air Compressors, UNDERHOOD40, UNDERHOOD70 (including Green Series Air Compressors), DTM70/DTM70-H, and VMAC Multifunction Power Systems, which include standby mode; ASME certified; includes fittings, 200 psi pressure relief value, tank drain, and 200 psi pressure gauge. Maximum pressure: Up to 200 psi Dimensions: 73.75″ (l) x 14.0″ (d); 187.3 cm (l) x 35.6 cm (d) Weight: 95 lbs (43.1 kg)
Heavy duty compressor air filter for moderate and heavy dust environments. Dimensions: 14.0” (l) x 6.0” (w) x 12.0” (h); 35.6 cm (l) x 15.2 cm (w) x 30.5 cm (h) Maximum flow: 80 CFM Weight: 10 lbs (4.5 kg)
Heavy duty compressor air filter for moderate dust environments. Dimensions: 14.0” (l) x 6.0” (w) x 12.0” (h); 35.6 cm (l) x 15.2 cm (w) x 30.5 cm (h) Maximum flow: 80 CFM Weight: 10 lbs (4.5 kg)
Cox Reel – P Series (P-LP-450RH) Sturdy single pedestal spring driven reel with space saving design facilitates workplace organization ½” x 50’ Max PSI: 300 Weight: Approx 48 lb Size: 7” x 18 5/8” x 17 1/8” External fluid path with machined from solid brass 90º full-flow NPT swivel inlet (Zinc plated steel swivel on HP models) Swivel Seals: NITRILE
OUR QUOTING PROCESS ALLOWS FOR HASSLE-FREE QUOTE SUBMISSION IN JUST A FEW MINUTES OR LESS!
WE ARE AVAILABLE MONDAY TO FRIDAY FROM 7:30AM - 4:00PM TO ANSWER ALL INBOUND INQUIRIES
TK Truck Body located in Edmonton, Alberta, is a truck/van body manufacturer and fleet repair shop.
16445 130 Ave NW, Edmonton, AB T5V 1K5
Phone: 780 447 9529
Fax: 780 447 2468
SALES: John office line 780 447 9535
PARTS: Mike E office line 780 447 9532
SERVICE: Tyler Trosko office line 587 416 2552